Current position > Product detail
『CMF025 Flow Meter: Micro Motion Elite Coriolis Mass Sensor Sizing Specs』Related information(v cone flow meter|rotary gas meter|gallon meter|gear meter|metal tube rotameter|glass tube rotameter|nutating disk meter|transit time ultrasonic flow meter|wedge flow meter|pd meters|hydraulic flow meter|ultrasonic water flow meter|water flow meter|air flow meter|magnetic water flow meter|oxygen flow meter|gas flow meter|argon flow meter|air velocity meter|gasoline flow meter|fuel flow meter|ultrasonic water meter|digital water meter|nitrogen flow meter|solid flow meter|Oxygen tank flow meter|digital water flow meter|diesel fuel flow meter|steam flow meter|02 flow meter|compressed air flow meter|oil flow meter|liquid flow meter)
CMF025 Flow Meter: Micro Motion Elite Coriolis Mass Sensor Sizing Specs
Quick Answer: The CMF025 size class is a small line Coriolis mass sensor for low flow liquid and gas measurement. Engineers size it by mass flow range, pressure drop, process connection, and fluid density. Silver Automation Instruments supplies DN6 and DN8 Coriolis mass flow meters that match the CMF025 footprint and output signal for most replacement jobs.
If you have a Micro Motion Elite CMF025 on your skid, you already know that the meter is not a simple pipe size decision. We get sizing questions from technical buyers in Vietnam, Thailand, Oman, Saudi Arabia, Chile, and Nigeria. Most ask the same thing. They need a reliable replacement or a second source for a DN6 or DN8 Coriolis mass flow meter.
Where the CMF025 Size Fits in a Plant
The CMF025 is common on chemical dosing skids, pilot reactor feed lines, perfume and flavor batching, solvent blending, and fuel additive systems. The line size is usually 1/4 inch or DN6. Some plants install it with a 1/2 inch process connection and a reduced bore. The actual flow range is smaller than the line size suggests.
In practice, a CMF025 class sensor handles liquid flow from about 0.3 kg/h to 2,200 kg/h. The exact number depends on fluid density and allowable pressure drop. A water line and a 0.7 kg/l solvent line will not behave the same even on the same DN6 body.
We have seen this on customer sites many times. A paint manufacturer in Southeast Asia replaced a CMF025 with a DN6 Silver Instruments Coriolis meter on a resin dosing line. The fluid was 40 cP. The line pressure was 6 bar. The meter worked well because we checked the viscosity effect before quoting.
Core Sizing Specs for a CMF025 Class Meter
Do not size a Coriolis meter by line size alone. These are the values that matter for a CMF025 replacement.
Mass flow range: 0.3 kg/h to 2,200 kg/h for liquid water at 1 bar to 2 bar pressure drop.
Process connection: DN6 or 1/4 inch NPT female, 1/4 inch butt weld, or 1/4 inch VCO style fitting.
Wetted material: 316L stainless steel as standard. Hastelloy C22 for acid, chloride, or seawater chemical lines.
Pressure rating: 100 bar at 20 °C is standard for many CMF025 class instruments. Higher ratings are possible but need a special body.
Process temperature: -50 °C to 204 °C for most standard models. High temperature versions can go higher but cost more and take longer to deliver.
Mass flow accuracy: ±0.10% of rate for liquids. Gas accuracy is usually ±0.35% of rate. Custody transfer versions may quote ±0.05%.
Density accuracy: ±0.001 g/cm³. This is useful when you use the same meter for batching and blend ratio control.
Temperature element: integrated PT100. The signal is available through the transmitter as a 4-20 mA HART output or Modbus RTU.
Most engineers skip this part. They compare the flow range only. Then the meter arrives and the pressure drop is too high. For a 50 cP resin at 1,500 kg/h, a DN6 tube can drop more pressure than the process pump allows.
How Silver Instruments Sizes a CMF025 Replacement
Send us four values. Mass flow range in kg/h. Operating pressure in bar. Operating temperature in °C. Pipe size in DN. That is the fastest path to a quotation.
Here is the thing. The CMF025 size is small. A DN15 meter is not always a good replacement. If your original connection is DN6 and your peak flow is below 1,200 kg/h, a DN6 body usually works. If you need lower
We also check density and viscosity. If you run liquid CO2, LPG, or naphtha, the meter calibration must cover the operating density. Tell us the fluid name and expected density at operating temperature. For water and light solvents, standard 316L wetted parts are fine. For chlorides or acid, use Hastelloy C22.
Last year a customer in Oman asked about a seawater flow meter for a desalination plant antiscalant dosing line. The pipe was DN6 and the flow range was 12 kg/h to 160 kg/h. The dosing water had a conductivity of 52 µS/cm. We recommended a DN6 Coriolis meter with Hastelloy C22 wetted parts and a 100 bar rating. That quote was accepted because we provided a specific pressure drop curve, not a generic catalog page.
Output and Certification Options for CMF025 Replacements
A CMF025 class replacement should give you the same signal as the original transmitter. Standard options include 4-20 mA HART, pulse, and Modbus RTU. Some plants ask for PROFIBUS PA or FOUNDATION Fieldbus. Silver Instruments can supply those on request.
Hazardous area approvals are critical. Most CMF025 installations in oil and gas or solvent plants need ATEX Zone 1 or IECEx Zone 1. The transmitter and sensor combination must be certified together. Do not mix an approved sensor with an unapproved transmitter.
For food and beverage sites, the wetted material and surface finish matter. A standard 316L sensor with Ra 0.8 µm or better is often enough for CIP and SIP systems. At a food plant in Thailand, the CIP return line had a conductivity of 8,500 µS/cm and the meter had to handle 85 °C cleaning cycles. Confirm the cleaning temperature and chemical concentration before you order.
FAQ: CMF025 Sizing Questions from Plant Engineers
Can Silver Instruments replace a Micro Motion Elite CMF025 sensor?
Yes. In most cases a standard Silver Instruments DN6 or DN8 Coriolis meter fits the same process connection and output signal. You need to confirm the wetted material, flow calibration range, and hazardous area requirement first.
What is the maximum flow for a CMF025 class sensor?
For liquid water, a practical maximum is around 2,200 kg/h. For gas, the maximum is set by inlet pressure and molecular weight. Always check pressure drop at your maximum flow rate instead of relying on a single maximum flow number.
What accuracy should I specify for a replacement?
Specify ±0.10% of rate for liquid mass flow and ±0.001 g/cm³ for density. If your site requires oil and gas custody transfer, request a lower uncertainty certificate and a proving report.
Which process connections are available for DN6 Coriolis meters?
Common options are 1/4 inch NPT female, 1/4 inch tube butt weld, and 1/4 inch VCO style fittings. Silver Instruments also supplies compression fitting adapters on request.
What information do you need for a quote?
Send us your pressure in bar, temperature in °C, pipe size in DN, and flow range in kg/h. Also include fluid name, density, viscosity, and hazardous area zone.
Get a CMF025 Size Quote from Silver Instruments
If you need a CMF025 class Coriolis mass flow meter, send your process data to Silver Instruments. We will respond with a sizing calculation and a quotation.
Tel: +86-25-68650347
WhatsApp: +86-25-52155837
WeChat: +86 15365082610
Send us your pressure (bar), temperature (°C), pipe size (DN), and flow range. Real process data gets a faster and more accurate quote.